Recommended chamber voltages

The operational voltages of ionisation chambers for radiotherapy are usually in the range 100 V to 400 V. However, there is little guidance about the best voltage for each chamber type.

Manufacturers usually indicate a range of values, and there is a tendency for users to adopt the highest voltage in this range, using the logic that recombination effects will be smaller. However, in some cases the higher voltage may result in charge multiplication in the gas, and so care should be exercised when choosing the voltage.

We recommend that the user should choose the highest voltage subject to the following conditions:

  1. the voltage is lower than the rating of the chamber and all HV connections, as specified by the manufacturer(s)
  2. the voltage can be supplied by all electrometers used with the chamber
  3. leakage from the chamber is small (less than 0.1% of the signal, and in absolute terms less than about 10 fA)
  4. ion collection is within the 'ion chamber' range (charge multiplication in the gas is negligible)
  5. the magnitude of the recombination correction is less than 2%.

Condition (iv) and (v) can be tested by using a Jaffé plot (a plot of 1/Q versus 1/V for voltages up to the operational voltage). To produce a Jaffé plot, measure the charge Q for at least ten voltages over the range V/6 to V. Plot 1/Q versus 1/V. This graph should have a linear region for the lower voltage range (where recombination is adequately described by Boag’s theory) and slowly become non‑linear for high voltages (that is, for small values of 1/V). If the operating voltage is in this non‑linear region, it means that there are other effects going on inside the ion chamber (charge multiplication in the gas, or higher order recombination effects) which are not modelled by Boag’s theory. Use of the two-voltage method for estimating the recombination in such cases will be less accurate. To get an idea of the uncertainty, compare the recombination correction obtained by extrapolating the linear part of the curve to 1/V = 0, with that obtained using the two voltage method at the highest voltage. If they differ significantly, choose a lower voltage.

Note that there is a subjective element to this choice. By choosing a high voltage the magnitude of the recombination correction is reduced, but the uncertainty in its determination is increased.

See reference below for more information.

Recommended polarity

The polarity of the applied voltage also needs to be selected by the user. We recommend, with no other reason than for the purpose of moving towards a national standard polarity, that users chose the polarity so that the CENTRAL ELECTRODE IS POSITIVE.

For plane-parallel chambers, we refer to the central electrode as the one connected to the central wire of the triaxial cable.

Note that there is no standard way to express the polarity of the voltage and different manufacturers use different conventions. For example, to set 250 V with the central electrode positive, Table 1 indicates the displayed voltage for different models.

Electrometer display when setting 250 V Central Electrode Positive (CEP), for several common manufacturers and models
Manufacturer Model Rear panel Electrometer display
PTW UNIDOS Webline No switch “-250 V”
PTW UNIDOS E “—” “-250 V”
IBA DOSE 1 No switch “250 V CEP”
Standard Imaging MAX-4001 No switch “100% 250Vdc”
Keithley/Fluke 35040 No switch “250 V CEP”
NE 2570 “—(NORMAL)” and “V (NORMAL)” No display
NE 2670 TYPE A, switch in left position “-250 V”

Suggested voltages

We suggest that 0.6 cc Farmer-type chambers be operated at 300 V CEP, and Roos type chambers be operated at 150 V CEP.



[1] Ion recombination correction factors (Pion) for Varian TrueBeam high-dose-rate therapy beams, Stephen F. Kry, Richard Popple, Andrea Molineu, David S. Followill, Journal of Applied Clinical Medical Physics, Vol. 13 , No. 6 , 2012.