Associated forms
Introduction
Subparagraph 7(d)(i) of the Australian Radiation Protection and Nuclear Safety Regulations 2018 (the Regulations) requires the CEO to make guidelines about how licence holders will report their compliance with the Australian Radiation Protection and Nuclear Safety Act 1998 (the Act), the Regulations and licence conditions. This document fulfils that requirement and provides information on when, how and what licence holders must report.
ARPANSA applies a graded approach to compliance reporting. The frequency of reporting is aligned with the regulatory priority of the source or facility. The regulatory priority is risk-based.
When to report
Licence holders are required to report quarterly, biannually (i.e. 6-monthly) or annually. The frequency of reporting is specified in Schedule 2 of the licence.
For licence holders who report quarterly, a report must be provided to the CEO of ARPANSA in an approved form within 28 days of the end of each quarter, i.e. by 28 January, April, July and October, or within such other period as determined by the CEO.
For licence holders who report 6-monthly, a report must be provided to the CEO in an approved form by 28 January and 28 July each year, or within such other period as determined by the CEO.
For licence holders who report annually, a report must be provided to the CEO in an approved form within 28 days of the end of the financial year, i.e. by 28 July each year, or within such other period as determined by the CEO.
To assist licence holders in timely reporting, an email reminder is sent to licence holders two weeks prior to the end of the reporting period.
How to report
Licence holders must use the Regulatory Administration Database (RAD) portal to submit the report, unless there are other agreed arrangements in place. The submission must use the form within RAD, or source inventory templates [1] are available on request.
Reports should be submitted by a person authorised to provide such information on behalf of the licence holder, such as a Radiation Safety Officer or the primary licence contact. Receipt of the report will be acknowledged by ARPANSA.
Please note that any documentation classified ‘Protected’ or above should not be transmitted via RAD or to a generic email address, please contact ARPANSA for further information.
What to report
The licence holder should address all matters in the report template. Guidance on the information required is provided below.
1. Notifiable incidents (section 58 of the Regulations)
Under section 58 of the Regulations, the licence holder must tell the CEO about a notifiable incident within 24 hours of it happening and give the CEO a written report about the incident within 14 days of it happening.
Guidance on what constitutes a notifiable incident for the purposes of section 58 is provided in Regulatory Guide: Radiation Incidents.
The licence holder should also provide a summary of any notifiable incidents that occurred during the reporting period.
2. Other incidents
Except as otherwise required by a special licence condition, the licence holder should report any other incident during the reporting period that had the potential to affect safety, but which was not notifiable under section 58 of the Regulations.
This may include any unintended event, including operating error, equipment failure, initiating event, accident precursor, near miss or other mishap, or any unauthorised act whether or not it was malicious, the consequences or potential consequences of which are not negligible.
For example:
- Loss of a Group 1 sealed source
- Minor contamination of laboratory clothing or work area
- Breach of operating limits and conditions
- Deliberate exposure of a personal monitoring device
- Incorrect settings on a safety system
- Sticking shutter mechanism on a radiation gauge
- Laser incident where there is the potential for injury
3. Personal monitoring
Part 6 Division 2 of the Regulations sets out the practices to be followed by licence holders with respect to dose limits (ionising radiation) or exposure limits (non-ionising radiation).
Any event where an individual is exposed to radiation exceeding a dose limit / exposure limit is regarded as a notifiable incident and must be reported under section 58.
Other unusual doses or exposures that required investigation or corrective action during the reporting period should be reported.
4. Acquisition of a source
The licence holder should provide a summary of sources acquired during the reporting period. Import permit numbers should be quoted where relevant.
When changes to the source inventory occur these must be updated in RAD. Updates can be made via the web portal at any time. Where required ARPANSA can provide the latest version of the source inventory to be updated by the licence holder and returned.
Before acquiring a source the licence holder should consider which of the following regulatory actions is required:
- New licence application
- Prior approval under section 63 of the Regulations
- Reporting a change to the source inventory under section 64 of the Regulations
For further guidance on the regulatory implications of making changes to the source inventory including acquiring, using, transferring or disposing of sources, see Appendix A.
5. Disposal of a source (section 65 of the Regulations)
The licence holder should provide a summary of any disposals made during the reporting period.
Licence holders should refer to Regulatory Guide: Disposal of controlled apparatus and controlled material. Disposals may require prior approval as well as updating the inventory that the disposal has taken place.
For further guidance on the regulatory implications of making changes to the source inventory including acquiring, transferring, disposing, or using new sources, see Appendix A.
6. Transfer of a source (section 65 of the Regulations)
The licence holder should provide a summary of any source transfers made during the reporting period.
Licence holders should refer to Regulatory Guide: Disposal of controlled apparatus and controlled material.
Transfer provisions also apply to infrequent sales, hires, loans, gifts, or donations within Commonwealth jurisdiction. Licence holders should notify the CEO about the transfer of a source using RAD, or where appropriate the Transfer Notice Form.
Transfers under subsection 65(3) must generally be reported within 7 days, unless the source is in security category 1, 2 or 3[2] in which case prior approval from the CEO of ARPANSA must be obtained before the transfer regardless of the jurisdiction to which it is being transferred.
Under subsection 65(5) of the Regulations the licence may make other arrangements with regard to source transfers such as where regular source transactions are part of routine operation and seeking prior approval for every transfer would be impractical. An example of such an arrangement is where there are regular sales of controlled material or controlled apparatus. Any alternative reporting arrangements will be specified in the licence.
Transfer of a controlled facility requires prior approval from the CEO under subsection 65(4) of the Regulations.
For further guidance on the regulatory implications of making changes to the source inventory including acquiring, using, transferring or disposing of sources, see Appendix A.
7. Corrective action arising from an inspection
The licence holder should report progress on any corrective actions arising from an inspection in accordance with the reporting requirements specified in the inspection report or covering letter.
8. Changes with significant implications for safety (section 63 of the Regulations)
The licence holder should provide a summary of any approvals sought and received under section 63 during the reporting period.
For guidance on how to categorise a change, licence holders should refer to Regulatory Guide: When to seek approval to make a change with significant implications for safety.
9. Changes unlikely to have significant implications for safety (section 64 of the Regulations)
Under section 64, licence holders must report any change that is unlikely to have significant implications for safety at least once every 3 months. Licence holders reporting quarterly will include this information in their quarterly report. However, licence holders reporting biannually (6-monthly) or annually must inform ARPANSA of the change within 3 months.
10. Review of plans and arrangements (section 61 of the Regulations)
Licence holders are required to review their plans and arrangements (and their safety analysis reports where applicable) at least once every 3 years and keep records of the review and any changes made.
When conducting the review, licence holders should refer to the Regulatory Guide: Plans and Arrangements for Managing Safety.
11. Compliance with special licence conditions
The licence holder should report progress against any special licence conditions. Any such conditions will be removed when compliance has been adequately demonstrated.
12. Breaches of licence conditions (section 57 of the Regulations)
ARPANSA encourages licence holders to find and fix their own non-compliance. Such behaviour reflects a healthy and robust safety culture. Whenever a potential breach is encountered, the licence holder has a responsibility under section 57 to investigate and rectify the breach including any consequences of the breach as soon as reasonably practicable.
The licence holder must tell the CEO as soon as reasonably practicable if a breach of a licence condition is identified. The quarterly/biannual/annual report must also include a summary of any breach reported during the reporting period.
Common breaches relate to:
Section 57A: A licence holder not taking all reasonably practicable steps to prevent and minimise human errors and organisational failures.
Section 60: A licence holder not taking all reasonably practicable steps to comply with their plans and arrangements.
Section 61: A licence holder not reviewing and updating plans and arrangements (and safety analysis reports where applicable) at least once every 3 years/not keeping records of the review.
Section 63: A licence holder not seeking the CEO’s prior approval to make certain changes that have significant implications for safety.
Section 65: A licence holder not seeking prior approval from the CEO or telling the CEO about movement of a source or facility, in particular failure to obtain prior approval before disposing of a source.
In many cases, the licence holder will be expected to perform a root cause analysis to fully investigate the potential breach. An investigation that involves a root cause analysis (to prevent recurrence) may take considerable time.
Appendix A: Regulatory implications of changes to the source inventory
Under section 62 of the Regulations the licence holder must keep an accurate inventory of sources it deals with. The approved form for maintaining this information is the RAD Portal, or using a source inventory spreadsheet (available on request).
The licence holder must consider the regulatory implications of making any change to the source inventory after the licence is issued.
Licence holders intending to acquire, relocate, transfer, dispose of, or modify a source or facility should refer to sections 63-65 of the Regulations and licence conditions to identify what action is required under the ARPANSA regulatory framework. It is particularly important to identify whether a proposed change requires the prior approval of the CEO of ARPANSA or, in some cases, whether a new licence application is necessary.
Licence holders should also refer to Regulatory Guide: When to seek approval to make a change with significant implications for safety to determine whether a proposed change requires prior approval.
A1. Adding to the source inventory
If the licence holder intends to acquire a kind of source that is not authorised by the existing licence (or any other source licence that the licence holder might have[3]) then a new application must be submitted with the appropriate fee and the licence must be amended and re-issued by ARPANSA before taking possession of the source. Failure to do so may result in a breach of subsection 31(1) of the Act.
Acquiring additional sources of a kind that is already authorised by the licence does not require prior approval but this is a change[4] for the purpose of section 64 of the Regulations and should be reported within 3 months or by the next quarterly report. Updates to the inventory can be made in the RAD Portal at any time.
Occasionally licence holders may discover sources in their possession that are not listed in their source inventory. These are often ‘legacy’ sources or sometimes non-ionising apparatus such as a Class 3B laser or UV source.
If a kind of source not covered by the licence is identified it may be necessary for the licence holder to apply for an authorisation to continue to possess, have control of, or use it. Advice should be sought from ARPANSA if there is any doubt about the status of a legacy source.
A2. Removing a source from the SIW
Under section 65 of the Regulations a licence holder must have prior approval from the CEO of ARPANSA to:
(i) dispose[5] of a controlled apparatus or controlled material (source)
(ii) transfer a source to another jurisdiction (outside of the Commonwealth)
However some exceptions apply; licence holders should refer to Regulatory Guide: Disposal of controlled apparatus and controlled material.
Transfers within the commonwealth, under subsection 65(3), must generally be reported within 7 days unless the source is in security category 1, 2 or 3 in which case the transfer must have the prior approval of the CEO of ARPANSA. This prior approval requirement comes from Radiation Protection Series No. 11 - Code of Practice for the Security of Radioactive Sources compliance with which is a statutory licence condition under section 59 of the Regulations. Failure to comply with sections 59 or 65 of the Regulations may result in the licence holder being found in breach of subsection 31(2) of the Act. Transfer can be applied for or notified via the RAD Portal.
Following transfer or disposal of a source, its status should be changed in the source inventory in RAD accordingly.
When an item no longer meets the definition of a controlled apparatus or controlled material the licence holder should change its status in the source inventory in RAD, and provide further details where relevant, for example: the source has decayed below the exemption limit or changes to the apparatus mean that it no longer meets the definition of a controlled apparatus.
A3. Licence holders with multiple divisions and/or multiple sites
Some licence holders have a number of divisions at one location or occupy premises spread over multiple sites. Each division may have a separate source licence and separate source inventory. The licence holder may also have one or more facility licences.
If a licence holder wants to undertake a new dealing in a particular division, the licence holder must determine whether section 63 of the Regulations applies or whether a new application is required. If the new dealing is not authorised by any existing source licence held by that organisation then a licence application is required. If the new dealing is authorised by an existing source licence, held elsewhere in the organisation, then section 63 applies.
If a licence holder wants to relocate a source from one division to another, from one site to another, or from one licence to another, the licence holder must determine whether a new licence application is required or whether section 63 or 64 of the Regulations applies under an existing licence. For example:
a) Relocation of a source within the same division at the same site
Section 64 of the Regulations applies; the licence holder must report the change to the source inventory within 3 months or in the next quarterly report. These updates can be made at any time via the RAD Portal.
b) Relocation of a source within the same division but at a different site
Section 64 of the Regulations applies if the source is to be used for the same as that described in the application and plans and arrangements, otherwise section 63 applies. These updates or applications can be made at any time via the RAD Portal.
c) Relocation of a source to a different division at the same site
Section 64 of the Regulations applies if the division receiving the source is authorised for the source type/dealing, and provided there are no implications for safety, otherwise section 63 applies (see Scenario 3). Note that subsection 65(3) of the Regulations also applies as the transfer of a source from one licence to another must be reported to ARPANSA within 7 days, except for security-enhanced sources that require prior approval. These updates or applications can be made at any time via the RAD Portal.
d) Relocation of a source to a different division at a different site
As for (c) above.
e) Transfer of a source from a facility licence to a source licence
A licence application is required unless the source type/dealing is authorised by an existing source licence. If authorised, then section 64 of the Regulations applies. Subsection 65(3) also applies - see (c) above. These updates or applications can be made at any time via the RAD Portal.
f) Transfer of a source from a source licence to a facility licence
If the facility licence already authorises dealing with this kind of source then section 64 of the Regulations applies. If not, then section 63 applies and approval from the CEO of ARPANSA must be obtained prior to the transfer. Note that dealing with the source must be included in the safety assessment report for the facility. These updates or applications can be made at any time via the RAD Portal.
Further guidance is provided in the scenarios and examples below. If there is any uncertainty about the regulatory implications of a proposed change to the source inventory, please contact ARPANSA.
Scenario 1: A licence holder wants to acquire a source of a type and for a dealing already authorised by the licence
In this situation a licence application is not required and the existing licence does not need to be amended. This is because the licence holder’s plans and arrangements for managing that type of source have already been assessed as satisfactory for the particular dealing. The change is regarded as unlikely to have significant implications for safety and is therefore subject to section 64 of the Regulations. These updates can be made at any time via the RAD Portal.
| Example 1: A licence holder is authorised to deal with a fully enclosed X-ray analysis unit (Group 1 Item 13). The licence holder wants to acquire another fully enclosed X-ray analysis unit. | No amendment to the licence is necessary. Section 64 of the Regulations applies: acquisition of the source must be reported within 3 months by updating the inventory. For most licence holders this will be by the next quarterly report. |
Scenario 2: A licence holder wants to acquire a source of a type not authorised by the licence
In most cases, a licence amendment application will be required.
| Example 2: A licence holder is authorised to deal with a fully enclosed X-ray analysis unit (Group 1 Item 13). The licence holder wants to acquire a partially enclosed X-ray analysis unit (Group 2 Item 11). | The licence holder must apply for a licence amendment to add Group 2 Item 11 before the apparatus is acquired. Once acquired, the licence holder must update their inventory. |
Scenario 3: A licence holder wants to relocate a source from the location specified in the source inventory
This is a proposed change to details provided in the licence application (or subsequently approved) and therefore a change relevant to either section 63 or 64 of the Regulations. The licence holder must decide which applies, that is, whether the relocation is likely to have significant implications for safety.
Prior to moving a source, the licence holder must consider such things as shielding, storage, security, and transport. If there are significant implications for safety in the process of relocation or at the new location, then prior approval is required under section 63. If there are unlikely to be any significant implications for safety, prior approval is not required but relocation of the source must be reported under section 64 within 3 months or in the next quarterly report.
| Example 3: A fixed industrial X‑ray unit located in Building A is to be relocated to Building B | This may have a significant effect on safety in terms of protective shielding, interlocks, warning lights, etc. Such a change would require the prior approval of the CEO under section 63 of the Regulations. |
| Example 4: The source inventory shows an unsealed source is being used in Laboratory C | If the licence holder relocates this source to Laboratory D with the same policies and procedures and with equivalent or better storage and handling, then the change is unlikely to have significant implications for safety. Such a change would fall under section 64 of the Regulations with no prior approval required. The change of location should be reported within 3 months or in the next quarterly report. The source inventory will also need to be updated. |
Scenario 4: A licence holder wishes to deal with a source that belongs to another organisation
There are certain situations where a licence holder may wish to use a source owned by another organisation. For example, a source may be leased, hired or borrowed, or a controlled person may be required to use another organisation’s source at that organisation’s premises.
Under section 13 of the Act, the definition of ‘deal with’ includes possession or having control of. Therefore, use of a source belonging to another organisation may only be undertaken if authorised by a source licence. In such circumstances the licence holder must consider whether the existing authorisation covers the proposed activity or whether an amendment to the licence or further licence application is required.
| Example 5: Licence holder (Y) wants to lend a sealed source to another Commonwealth licence holder (Z) for a particular project | Licence holder Z must be authorised for the proposed dealing. The transfer of possession is covered by paragraph 65(2)(b) of the Regulations and must be reported to the CEO within 7 days. In this case, the source inventory of licence holder Y should be amended to indicate that the source is temporarily on loan. The source inventory of licence holder Z should also be amended to include the source until it is returned. In any case the temporary transfer should also be reported in accordance with section 64. Similarly, the return of the source should also be reported and the source inventories amended as appropriate. Note: Changes to the source inventory are only relevant if the loan is for an extended period, i.e. more than 3 months. Short-term loans should still be reported in the compliance report to ARPANSA. |
| Example 6: A source licence authorises the licence holder to deal with baggage X-ray units. The licence holder leases an additional baggage X-ray unit from an equipment supplier | The licence holder must report the additional source by updating the inventory within 3 months or by the next quarterly report. Eventual return of the sources to an organisation outside the Commonwealth’s jurisdiction requires prior approval. |
| Example 7: A source licence authorises dealings with a fully enclosed analytical X-ray unit. In a collaborative venture with a university, it is proposed that a controlled person covered under the source licence will use a fully enclosed analytical X-ray unit owned by the university at the university’s premises. | This dealing is authorised under the source licence. The CEO should be advised of this dealing under section 64 of the Regulations. The conditions attached to the licence with respect to this kind of controlled apparatus are still applicable. Where direct compliance with these conditions is outside the control of the licence holder (as in the case of equipment maintenance) it is the responsibility of the licence holder to be satisfied that the conditions have been met and to provide supporting evidence to ARPANSA if required. For example, the licence holder may be required to provide ARPANSA with the licensing or registration information from the relevant State/Territory regulatory authority. |
[1] The report templates are designed for electronic use; the printed version may not display all data.
[2] Refer to Radiation Protection Series No. 11 - Code of Practice for the Security of Radioactive Sources compliance with which is a statutory licence condition under section 59 of the Regulations.
[3] Refer to Licence holders with multiple divisions and/or multiple sites section of this guide.
[4] The definition of a ‘change’ for the purposes of sections 63 and 64 of the Regulations is: a change to the details described in the application for the licence; or a modification of the source or facility.
[5] Disposal of controlled apparatus for the purpose of subsection 65(1) of the Regulations includes destruction.
